Ons forum is al ruim 20 jaar in gebruik en een rijk archief. Voor robot bouwers is het een plek om updates en foto’s te delen van hun projecten. Voor een snelle reactie op je vragen zijn wij het meest actief op facebook en discord.
flex schreef:2.1 LED will stayS on? Gum die S even weg...
3.4 than closes after that Zet een punt achter closes en dan natuurlijk een hoofdletter bij after. Zowel voor hit als ook srimec.
En ik mis het hydro/KanOpener programma.
Beschrijf het in de juiste bewording en ik maak het
Ik heb de taal nog niet 100% nagekeken dus dat kan goed kloppen.
Alle programma's zijn welkom, ik kan er zoveel inzetten als praktisch is.
2.1, eerste zin.
While powering on the device press down and hold the program button for 7 seconds, during this time the LED will stay on.
3.4
STICK IS UP HIT!
Relay 1 pulses open for 0.5 seconds, then closes. After that relay 2 will open for 0.75 seconds. If the stick is still in the up position after 1.5 seconds, relay 2 will open again for as long as the stick is in the up position. ( maybe the axe is stuck and it needs extra force)
STICK IS DOWN, SRIMEC MODE
Relay 1 pulses open for 1 seconds, then closes. After that relay 2 will open for 0.75 seconds. If the stick is still in the down position after 1.75 seconds, relay 1 will open again for as long as the stick is in the down position. ( maybe the robot needs extra srimec power.) After the stick is returned to the middle position relay 2 will open for 0.75 seconds.
Niels Schotten
DRG Arena marshall & Judge
"Hard Work Often Pays Off After Time, but Laziness Always Pays Off Now."
Every once in a while you need to take your foot out of your mouth and up against your rear to kick our ass in to gear...
Bullfrog zou ik net als Gravity doen, want dat is één burkert om te vuren (Burkert opent op zijn beurt weer een grotere klep), en één burkert om te dumpen.
Kan-opener program:
Up: Power the hydraulic pump
Down: Power the hydraulic pump + open hydraulic valve
Up to center: Stop pump
Down to Center: Stop pump, wait 1 second, close valve.
Mvg,
Leo van Miert Team RCC website.
Gentlemen, no fighting please. This is, after all, a council of war.
Kan-opener program:
Up: Power the hydraulic pump
Back down to center: Stop pump
Down: open hydraulic valve + Power the hydraulic pump *
Back up to Center: Stop pump, wait 1 second, close valve.
* mag een korte delay (0,1s) op de pomp zodat je zekerder bent dat de klep reeds geschakeld is.
(iets logischere opbouw)
Niels Schotten
DRG Arena marshall & Judge
"Hard Work Often Pays Off After Time, but Laziness Always Pays Off Now."
Every once in a while you need to take your foot out of your mouth and up against your rear to kick our ass in to gear...
Prototype V2 print en componenten zullen de komende 2 weken binnen komen. Met die print even kijken of ik ook een low voltage indicator kan maken, die past dan bij TMHWK / Basic a / Can opener op relais 3, tot op heden even nog niet beschreven omdat ik dat eerst helemaal wil testen.
Nog even een veiligheidsfunctie die ik wil voorleggen:
Als de SBS opstart of uit failsave komt en de stick staat dan direct hoog of laag, gaat hij pas reageren op het programma als de stick in de neutrale positie is geweest ?
Relay 2 will open and after 100ms relay 1 will open as long as the stick is down. If the stick goes back to neutral relay 1 closes immediately. Relay 2 will close after 1 second.
En je hebt de tabel aan het eind nog niet aangevuld...
Had de relais werwisseld bij het afschakelen, text van mij weer aangepast. (relais 2 is de klep)...
Laatst gewijzigd door flex op za nov 29, 2014 12:24 am, 1 keer totaal gewijzigd.
Niels Schotten
DRG Arena marshall & Judge
"Hard Work Often Pays Off After Time, but Laziness Always Pays Off Now."
Every once in a while you need to take your foot out of your mouth and up against your rear to kick our ass in to gear...
als je een goede gebruiksvriendelijke relaismaakt ontwerp er dan ene die zelfs ik kan aansluiten ...ga er vanuit dat je klant geen echt verstand van elektronica heeft en dus een duidelijke handleiding of zoiets ...
iceman schreef:als je een goede gebruiksvriendelijke relaismaakt ontwerp er dan ene die zelfs ik kan aansluiten ...ga er vanuit dat je klant geen echt verstand van elektronica heeft en dus een duidelijke handleiding of zoiets ...
Vandaar dit document : https://dl.dropboxusercontent.com/u/861 ... h%20V2.pdf
Ik voeg nog wat aansluitgegevens, trouble shooting en tekeningen toe.
Is het gebruik van Engels lastig voor je, gezien de gebruikers van het product ben ik automatisch in het Engels gaan schrijven.
The SBS is build for a uncommon task, it is not a toy.
Naar:
The SBS is build for an uncommon task, it is not a toy.
en
1. Do not try to modify, puncture the SBS Send me an email and I be happy to design a modified version for you.
Naar:
1. Do not try to modify or puncture the SBS. Send me an email and I will be happy to design a modified version for you.
En
5. If there is smoke coming out of the SBS it is not just exited to go in to battle, it needs the smoke to stay inside
of the components. Please don’t use it anymore!
naar:
5. If there is smoke coming out of the SBS, it is just not exited to go in to battle. It needs the smoke to stay inside of the components. Please don’t use it anymore!
Niels Schotten
DRG Arena marshall & Judge
"Hard Work Often Pays Off After Time, but Laziness Always Pays Off Now."
Every once in a while you need to take your foot out of your mouth and up against your rear to kick our ass in to gear...